Home > Error Code > Hitachi Inverter Error Codes

Hitachi Inverter Error Codes

Contents

Skip to main content Search Global Hitachi GroupProducts & Services Hitachi GroupCorporate Information 日本語 Sitemap Contact Us Company Profile Products Application Catalog Global Network Trade Show Schedule Home Products Information Inverter E19 Inverter thermal detection system error When the thermal sensor in the inverter module is not connected. How to access the details about the present fault Note Indicated inverter status could be different from actual inverter behavior.e.g. Your cache administrator is webmaster. Source

This feature protects the inverter, and does not protect humans. Please try the request again. Turn off the inverter power once. However, in most cases the help of a service engineer is indispensible.

Hitachi Error Codes

Incorrect Wiring Connection to PCB in Outdoor Unit 39SystemAbnormality of Running Current at Constant CompressorOvercurrent, Melted Fuse of Failure of Current Sensor 43PressurePressure Ratio Decrease Protection ActivatingFailure of Compressor, Inverter 44PressureLow are common with FSG and FS3 series. ** : For only 24, 30FSG1/FSG5 (220V 60Hz), *** : In case of PC-2H2 Room Air Conditioner range: Indoor unit alarm codes If timer Air inlet or coil thermistor not connected, open or short circuited faulty PCB 10Indoor fan motor over current or abnormal rotation speed. E25 Main circuit error (*3) The inverter will trip if the power supply establishment is not recognized because of a malfunction due to noise or damage to the main circuit element.

E36 Braking error When "01" has been specified for the Brake Control Enable (b120), the inverter will trip if it cannot receive the braking confirmation signal within the Brake Wait Time Please try the request again. Check pump operation and drain 07Drain pump forced operation. Hitachi Split Ac Red Light Blinking Generated Thu, 24 Nov 2016 08:47:31 GMT by s_hp106 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection

E81 Excessive speed If the motor speed rises to "maximum frequency (A004) x over-speed error detection level (P026)" or more, the inverter will shut off its output and display the error Furnace and Air Conditioning Repair, Service & Installation Customer Satisfaction is our Business Menu Skip to content HomeAbout UsAir conditioner installation layoutAir conditioner make a noiseAir Conditioning And Your HealthBryant Air E30*2 Driver error An internal inverter error has occurred at the safety protection circuit between the CPU and main driver unit. LD 302 FlashesFlashesThermistor that is faulty 1Compressor overheat (OH) 2Defrost thermistor 3Ambient thermistor 4Narrow pipe (expansion) thermistor, for circuit 1 5Wide pipe (suction) thermistor, for circuit 1 6Narrow pipe (expansion) thermistor,

Sometimes, error codes can give you enough information to fix your Hitachi air conditioner on your own. Hitachi Ac Error Code E9 Power Supply OFF. 04InverterAbnormality between Inverter and Control PCBFailure in Transmission between PCBs 05TransmissionAbnormality of Power Source WiringReverse Phase Incorrect Wiring 06Voltage DropVoltage Drop by Excessively Low or High Voltage to The system returned: (22) Invalid argument The remote host or network may be down. Faulty motor or PCB 13Eprom data error.

Hitachi Excavator Fault Codes

Ref. If an over-voltage condition exists, the inverter enters a fault state. Hitachi Error Codes Slim air conditioner error codesPanasonic air conditioner error codesPanasonic cassette air conditioner error codesSamsung air conditioners error codesSamsung free joint multi air conditioner error codesSanyo Wall Mounted Air conditioner error codesSharp Air Conditioner Error Codes Failure of Other Indoor Unit of the Same Refrigerant Cycle. 35SystemIncorrect Setting in Indoor/Outdoor Unit No.Existence of the same Indoor Unit No.

If LD 303 is on permanently this is normal operation. http://igroupadvisors.com/error-code/hitachi-ac-error-codes.php Reply Tin Ko says: October 29, 2016 at 10:33 pm 31 Reply Leave a Reply Cancel reply Your email address will not be published. E60to E69 Option error The inverter detects errors in the option board mounted in the optional slot. E22 CPU communication error When communication between two CPU fails, inverter trips and displays the error code. Hitachi Wj200 Error Codes

The system returned: (22) Invalid argument The remote host or network may be down. are common with FSG and FS3 series. ** : For only 24, 30FSG1/FSG5 (220V 60Hz), *** : In case of PC-2H2 Failure of Thermistor, Sensor, Connection Related posts: Hitachi Split System Your cache administrator is webmaster. have a peek here Leakage, Clogging or Expansion Valve Close Lock. 09 Outdoor Unit- Tripping of Protection Device- Failure of Fan Motor 11 Inlet Air Thermistor-Failure of Thermistor, Sensor, Connection 12 Outlet Air Thermistor-Failure of

E50 to E59 EzSQ user trip (0 to 9) When user –defined trip happens, inverter trips and displays the error code. Hitachi Split Ac Red Blinking And Ac Not Working Generated Thu, 24 Nov 2016 08:47:31 GMT by s_hp106 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Failure of PCB.

Failure of PCB.

E14*2 Ground fault The inverter is protected by the detection of ground faults between the inverter output and the motor upon during power up tests. E12 External trip A signal on an intelligent input terminal configured as EXT has occurred. Generated Thu, 24 Nov 2016 08:47:31 GMT by s_hp106 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection Hitachi Wj200 Inverter Manual The Unit Identification A* etc is shown along with the Code Number for the Fault that has occurred.

E80 Encoder disconnection If the encoder wiring is disconnected, an encoder connection error is detected, the encoder fails, or an encoder that does not support line driver output is used, the Display will flash as shown in diagram. E08*2 EEPROM error When the built-in EEPROM memory has problems due to noise or excessive temperature, the inverter trips and turns OFF its output to the motor. Check This Out Tripping of Fuse.

Your cache administrator is webmaster. E02 Over-current eventduring deceleration E03 Over-current event during acceleration E04 Over-current eventduring other conditions E05*1 Overload protection When a motor overload is detected by the electronic thermal function, the inverter trips If timer lamp flashes for a number of times and then pauses, please reference table below.

© Copyright 2017 igroupadvisors.com. All rights reserved.