Sorry for the delay. The part number for the relay board is 316443918 You can order the part by clicking on the part number. The one in question is black colored. Thank you, Gene. have a peek here
louis Posts 16 Ok, pulled the range out again, no model # any where. Had a F10 error code. Sign up! Actually it is always the safest way. http://www.applianceblog.com/mainforums/threads/28521-electrolux-error-F10-code
If parameters are not correct, the activated functions are stopped and the corresponding error code (the letter "F", followed by numbers) appears. If the sensor and wiring are good, replace the EOC. Expand Popular Products GE Profile Spectra JGBP90 Gas Kitchen Range 1,217 Questions Maytag MER6772 Gemini Electric Kitchen Range 479 Questions Kenmore 79012 / 79014 / 79019 Gas Kitchen Range 417 Questions
This happens every time and we have used different oven thermometers in case one was defective. The lock motor may be powered as in above step to open and close lock switch. We could, at that time, reset it and turn the oven back on. F10 Error Code Kenmore Oven The fan motor does work.
Thanks again for all your time and help!! Electrolux Oven F11 Error Code Frank // Mar 10, 2015 at 7:45 am Gene, Thank you for the advice. I can't help but worry there is a bigger issue, this time this was NOT relatively close to a self clean, which I have read can be a cause of electrical http://www.youserguide.com/wiki/Electrolux_318127019-006 All rights reserved. © Applianceblog.com 2004 - 2016 Search Fixya Press enter to search.
Bad EEPROM Identification/Checksum error. 1. (F10 only) Check *RTD Sensor Probe & replace if necessary. Thank you for your question. There is no a separate keypad in your range. You can try to use the old one but if you damage it, the part number for the overlay is 316419700 Good luck and keep us posted.
Ed // Apr 23, 2015 at 6:03 am Hello Gene. https://grupomarcservice.com/electrolux-aeg-manual-codigos-de-error-hornos/ Frank // Feb 27, 2015 at 5:51 pm Hi Gene, You helped me back in November with a F10 error. Electrolux Oven Error Codes Gene. Frigidaire Oven F10 Reset Measure the resistance between the wires connected to these pins.
After we took it out, the stove started beeping continuously and it showed F10 on the ... http://igroupadvisors.com/error-code/how-to-fix-a-225-error.php F15 Controller self check failed. I was reading your site and trouble shooting. Sad news. F10 Error On Frigidaire Oven
George // Dec 19, 2014 at 10:54 am Hi Gene, thanks for the reply! Gene. What to do to repair? http://igroupadvisors.com/error-code/how-to-fix-internal-error-error-code-13.php The problem has worsened as now the PF code will come up whenever the oven (bake/broil) is selected.
Me alegro que en parte haya solucionado. Thanks…(.Not a good time for an oven to not work as gotten cook the Christmas bird on Thursday. What should I focus on next?
Now it wont let me set the clock to the right time. Cut off the wires at the plug which goes to the EOC, leaving about 3″ to 4″ to splice a new wires. OWNER RICK'S APPLIANCE REPAIR APPLIANCE TECHNICIAN FOR 31 YEARS REFRIGERATION SPECIALIST ONLINE SERV TECH: ApplianceBlog.com CERTIFIED TYPE 1; TYPE 2.....REFRIGERATION SERVICE E.S. The part number is WB2X9998 Good luck and keep us posted.
Keep me posted. Valerie // Apr 24, 2015 at 7:00 am Hi Gene, I am having problems again and before I order on my diagnosis, I wanted your confirmation. In such situation the solution is to replace the Electronic Oven Control (EOC). http://igroupadvisors.com/error-code/how-to-fix-error-631.php I just wanted to let you know, the relay board did indeed solve the issue.
Do you have a suggestion as to which board is acting up? AppliancePartsPros.com Happy New year! Gene. Don't show me this message again.
Any ideas what is wrong? Unfortunately this part has been discontinued by the manufacturer and is no longer available. I have press the cancel button and it continues to beep. For the EOC it gives part #ES630, but when I search for it no results.
I even removed the back panel and there wasn't one. Gene. I am lost as to how to proceed next as the touchpad was included with the new EOC? When I searched for a part it appears you can't just replace the ribbon connector, but have to replace the whole TST panel ($600!!).
El horno se reconecta automáticamente cuando desciende la temperatura. George // Dec 22, 2014 at 3:32 pm Hi Gene, thanks I really appreciate your time.