Home > Error Code > Hot Tub Error Code Ep

Hot Tub Error Code Ep

Contents

LF, or Low Flow error codes on a spa or hot tub is really a self-preservation exercise for your hot tub. Page 41 Warranty Information under any circumstances be covered by the MANUFACTURER. One of the sensors has detected that the spa water is 110°F. The equipment stays on until the sensors detect that the spa temperature has risen to within 8.0°C of the set temperature. http://igroupadvisors.com/error-code/how-do-your-fix-error-code-107.php

Page 33 Heavy Cleaning or Decontamination On occasion, it may be necessary to “Super Sanitize” your spa. FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. Use a spa immediately after strenuous exercise. Sometimes, it's actually a bad pressure switch or flow switch, or loose connections or damaged wires or wire connectors. https://spacare.com/commonspasideerrorcodes.aspx

Balboa Hot Tub Error Codes

The other pumps and the blower will purge for 30 seconds to 2 minutes at the end of the freeze condition. Check to be sure the filter and filter basket are free of debris. Press any button to reset or wait 15 minutes and spa will automatically reset. Water temperature is unknown. 2.

After severe weather, which may include power surges that you do not notice, your spa may display an error code. When the auxiliary sensor reads around 40F- (actual temperature dependent on specific auxiliary sensor used), the system provides freeze protection. If your spa model is equipped with a cord, do not bury the cord. Marquis Spa Error Codes Page 7 Never replace suction fitting with one rated less than the flow rate marked on the original suction fitting.

Shut the spa power off, remove the filter and make sure all the jets are open. Spa Error Codes rdr Every 90 days Drain and refill spa rC0 Every 180 days Clean and condition spa cover rtr Every 180 days Treat wood panels rCH Once a year Replace the filter Page 28 The cycle will rotate back to “rtc”. https://www.spaparts.com.au/page/information/spa-error-codes-or-messages/ FINAL NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets.Other issues that can cause these error

Make sure they aren't touching anything. Great Lakes Hot Tub Error Codes The spa must be set on a level cement slab and/or a level deck surface that is sufficient to support the entire length and width of the spa. If the spa surface is repaired, the repair is limited to the affected area only, and there is no guarantee against discoloration or fading. If flashing by itself, spa is shut down.The Panel Displays Cd, CLd:This indicates that a sensor detects a possible freeze condition.

Spa Error Codes

Clean the filter/skimmer if there is any blockage. https://www.poolandspacentre.co.uk/help/hot-tub-and-spa-error-codes.html It is the responsibility of the spa owner to insure that the spa is accessible for repairs. Balboa Hot Tub Error Codes Page 43 The LAGUNA BAY SPAS warranty is terminated if the spa has been subject to alteration, misuse, or abuse. How To Fix Flo Error Hot Tub Page 25 The Pump 1 “HIGH” icon will be displayed on the LED Press the button a third time to turn Pump 1 “OFF”.

After all the sodium Di-Chlor has been added turn all pumps on their highest speed and allow the water to circulate for one hour. his comment is here The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open Each time you change the water in the spa, you should check to be sure the locks on the slice valves are in good condition;... Misuse or abuse is defined as but not limited to: use of spa in non- residential situation, water temperatures outside the range of 32 to 110 degrees, damage... Vita Spa Error Codes

You can leave a response, or trackback from your own site. YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART. If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa. this contact form Rotomolded Spas Spa Preppers - Hurricane Spa Protection Hot Tub Circulation Pump Troubleshooting How to Measure for a Hot Tub Cover Hot Tub Electrical Safety Spa & Hot Tub Plumbing Fittings

Standard building practices must be followed. Great Lakes Hot Tub Troubleshooting Do not leave the spa unattended while the cover is removed. Push the valve inward so it is flush with the frame.

Control Panel Messages Table Control Panel Messages Problem Messages (Requires action) Information Messages (No action required) Operation Modes Reminder Messages No message oncontrol panel -- Ecn rPH dr --- 5LP r5A

Check the water level. Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way. See M7 Sensors here. Hydropool Hot Tub Error Codes Check to be sure no water is draining from the drain valve as you refill the spa.

In extremely hot weather, check for proper cabinet ventilation. Page 8 (98.6ºF). Don't show me this message again. navigate here A buried cord may result in death or serious injury due to electrocution if direct burial-type cable is not used, or if improper digging occurs.

Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Make sure spa is filled to proper level and that pumps are primed and filter cartridges are clean. NOTE: Temperature sensors should be mounted in a sensor mount in the wall of the spa and not behind the shield on the heater manifold with the hi limit sensor. If you are unsure of something or have any questions, please do not hesitate to contact us via Email.

See below for further explanations: FLO, FLC, FL, FL1, PS, Blinking LightsPressure/Flow Switch Failure:These codes are related to flow issues or the pressure switch/flow switch and are by far the most ft. Flow problems are the number one source of trouble for the spa or hot tub owner. The sensor that is plugged into the sensor “A” or “B” jack is not working.

Fill out my Wufoo form! drY, dY Insufficient water detected in heater. The pumps and the blower will automatically activate regardless of spa status. Note: A common programming mistake is overlapping filter times that may cause the spa to filter continuously.

The fundamental reason is water flow through the spa control system, if the water is not flowing at a rate to satisfy the pressure switch, it will result in one of The means of disconnection must be readily accessible, but must be installed at least five feet (1.5m) from the spa. PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. Power up and turn on low pump.

Quick View Order Status Wishlist (0) Cart - $0.00 Checkout Your One Stop Spa Parts Site ™ Search Menu Categories Cart (0) Account Home About Us Information International Customer Information Today, Cal Spas™ is a renowned Global Manufacturer of Home Resort Products. Then you have to check if the flow of water is sufficient in the heater and to remove the air by unscrewing it. Your cache administrator is webmaster.

If algae develops, simply draining and refilling the spa will not kill the algae.

© Copyright 2017 igroupadvisors.com. All rights reserved.