Home > Error Code > Hot Tub Error Code Hl

Hot Tub Error Code Hl

Contents

I cant find anything on why the temperature would be flashing. Make sure your filter is clean and the slice valves (sometimes called knife or gate valves) are open completely to ensure adequate flow. And can they be tested? Rare system error. http://igroupadvisors.com/error-code/how-do-your-fix-error-code-107.php

Categories Accessories Chemicals Cover Removers Covers Filter Cartridges (Unicel) Filters Cartridges (PuraSpa Disposable) Fragrances Gift Ideas & Fun Stuff Ozonators Parts Department Pumps & Air Blowers Rubber Ducks Spa Packs (Heater This is done by pressing the large red button on your spa pack. 2) Check your spa thermostat. Heater is deactivated. or SpaDepot.com customers with accounts enjoy these benefits: Faster checkout Order status & history Easier package tracking Manage addresses Favorites list Exclusive deals CREATE ACCOUNT SHOP AS GUEST All Products http://www.hottubessentials.com/troubleshooting_tripping_high_limit.htm

Hot Tub Error Codes

Heater is shut down, but other spa functions run normally. Remove spa heat cover to allow the water temp to cool down. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. I recently had new bearings and seals in the circ.

Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times Contact ACC. pump and it seems to be working so I doubt it is a flow problem. Marquis Spa Error Codes Water and electricity do not mix and carry the risk of electrical shock.

Open the spa cover to allow excess heat and steam to escape. Balboa Hot Tub Error Codes Low Water Flow (LF, FLO), is the usual cause of an overheating (OH, OHH) spa or hot tub. Up next Dimension One Spa Low Flow FL or FLC Error - Duration: 3:40. see this It should heat back up to 104 after a short period of time.

I hope that I dont have another leak, It is far to cold outside to be taking the sides off. Great Lakes Hot Tub Error Codes Once this is done check ACROSS the heater element post, you should have either 110 volts or 220 volts depending on what voltage is operating the control box. No more HL reading which is good. Yes, this is VERY common on some of the Maax tubs, especially with extended filtration times.

Balboa Hot Tub Error Codes

Heater is deactivated. https://spacare.com/commonspasideerrorcodes.aspx How often do these HL sensors go? Hot Tub Error Codes Now it is heating back up, I hope.So does HL also come on when the temp drops 4 degrees? How To Fix Flo Error Hot Tub HL sounds like a high limit error - where your spa thinks it's 118 or so degrees.

It is a safety feature to prevent your equipment from being damaged by extreme heat. his comment is here Spa Overheating Troubleshooting Flow Chart Here's a Cal Spa troubleshooting flow chart that has some other possible triggers of seeing OH, OHS, OHH or HH blinking on your spa panel. It trips the HL error code to turn the heater off to prevent more heating. Press any topside button to reset a digital spa after the water has cooled to 100° F. Vita Spa Error Codes

Watch Queue Queue __count__/__total__ Find out whyClose Dimension One Spas High Limit HL Error Easy SpaParts SubscribeSubscribedUnsubscribe Loading... Share this post Link to post Share on other sites ps558 0 Spa Guru Members 0 1,117 posts Posted December 4, 2009 · Report post My Maax spa is getting Continue through this troubleshooting list only if the problem persists.) How to troubleshoot a high limit switch that is tripping: 1) Reset the high limit switch. this contact form Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way.

I recently had new bearings and seals in the circ. Arctic Spa Hl Error Code Pump may also be deactivated). FL1 = Water flow problem, inhibited or pressure switch malfunction.

Sn2 = Nonfunctional temperature sensor.

One sensor has detected 118° F at heater. When you reset the GFI and the HL went away, it was nothing major at all. What model tub do you have? Reset High Limit Switch Hot Tub William Kasper 25,211 views 10:12 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Duration: 9:09.

This feature is not available right now. Easy SpaParts 1,478 views 3:40 Fixing A Cold Hot Tub... - Duration: 10:12. That causes me some concern because HL should not be coming on during temp drop, that is counter productive.If the HL protects overheating, then when temperature is water drops drastically the navigate here This would all make senseBut what about the flashing temperature???

And can they be tested? Replace the thermostat if you can't get it to function properly. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Use any of the information contained in this article at your own risk.

Share this post Link to post Share on other sites Create an account or sign in to comment You need to be a member in order to leave a comment Create Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. How often do these HL sensors go? If the probe sticks out, it may not be reading the water temperature.

drops. Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice. So then I reset the GFI and the tub shows current temp at 100 when it is set to be 104. Std = Spa operating in Standard Mode.

The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes. Spa is shut down. How often do these HL sensors go? Hot Tub Essentials will not be held liable for any injuries that may result from the troubleshooting or installation of any electrical components in your spa.

If you are unsure of something or have any questions, please do not hesitate to contact us via Email. I have seen were the filter cycles are set to long and it drives the heat up and gives a HL error. You may choose to test the temperature that the high limit trips at.

© Copyright 2017 igroupadvisors.com. All rights reserved.