Home > Error Code > Hot Tub Error Codes

Hot Tub Error Codes

Contents

If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open If flashing by itself, spa is shut down. You can also check the pressure switch or flow switch with a an Ohm meter. th2/current temperature On startup indicates temperature probe problem. Check This Out

Check for clogged filter. The other pumps and the blower will purge for 30 seconds to 2 minutes at the end of the freeze condition. FINAL NOTE: Most spas are equipped with pressure switches and can be found threaded into the stainless steel heater manifold. Status of the heater element is unknown. https://spacare.com/spasideerrorcodes.aspx

Balboa Hot Tub Error Codes

SE = Spa operating in Standard-in-Economy Mode. System will restart when temp. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional. SESH = Sensor short, nonfunctional.

Spa has shut down. FLO, FL, FLC, FL1, PS, Blinking Lights Pressure Switch or Flow Switch Failure. This must be repaired only be a Sundance Spas dealer or qualified service technician. Coleman Spa Error Codes You must be logged in to post a comment.

Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Vita Spa Error Codes No action is necessary. OH = Over heat. Spa Error Codes: Sn, Sn2, Sn3, EO, E1, Prr With these spa sensor codes, the Temperature Sensor is open or shorted.

PnL Communication between the panel and circuit board is faulty. ---- Watchdog" (spa is deactivated) A problem has been detected. Hot Tub Error Code Oh Spa has shut down. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". Sn2 = Nonfunctional temperature sensor.

Vita Spa Error Codes

Sensor plugged into jack B is not working. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ NOTE: Temperature sensors should be mounted in a sensor mount in the wall of the spa and not behind the shield on the heater manifold with the hi limit sensor. Balboa Hot Tub Error Codes The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open Marquis Spa Error Codes Other issues that can cause these error codes one or more of the service valves is not open up all the way.

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. http://igroupadvisors.com/error-code/hot-tube-error-codes.php No action is necessary. Contact qualified service technician. Rare system error. How To Fix Flo Error Hot Tub

HFL Substantial difference between temperature sensors detected. F2 Panel sensors have been pressed too many times in a short period of time. If your water flow is perfectly fine, then you could have a problem with the thermostat or high limit switches used on older spa packs, which could fall out of calibration, http://igroupadvisors.com/error-code/hot-tub-error-codes-dr.php No action is necessary.

OH Overheating, water over 112° F. Gecko Spa Pack Error Codes Check for proper spa water level and ensure pump is primed. One sensor has detected 118º F.

Protect from FreezingCover Cleaning and AdviceAcrylic Surface Care and MaintenancePurchase a "Made for Michigan" Spa Cover>Spa Cover MeasuringPurchase a Spa Cover Lift AssistantWhirlpool & Air Bath TubsSystem Cleaning-Home remedyAcrylic Surface Care

Spa Overheating Troubleshooting Flow Chart Here's a Cal Spa troubleshooting flow chart that has some other possible triggers of seeing OH, OHS, OHH or HH blinking on your spa panel. Spa unusable. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. Coast Spa Error Codes PnL Communication between the panel and circuit board is faulty. ---- Watchdog" (spa is deactivated) A problem has been detected.

Water temperature has reached 118ºF. SESH Sensor short, nonfunctional. You can leave a response, or trackback from your own site. navigate here F4 Circuit Board temperature has exceeded acceptable limit.

ICE Freeze protection. For the complete list of error codes click here. NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets. If alternating with temp, may be temporary condition.

If you confirm all those things, and it still throws an Sn error at you, test the sensor as described above; it may be faulty. LF, or Low Flow error codes on a spa or hot tub is really a self-preservation exercise for your hot tub. PSoL Pressure switch open with low pump. Entire system is disabled.

One sensor has detected 118º F at heater. Switch closed while pump is deactivated. Pressure switch is not working.SN = Non functional high temperature sensor. COL = Cool condition.

© Copyright 2017 igroupadvisors.com. All rights reserved.