Home > Error Code > Hot Tube Error Codes

Hot Tube Error Codes

Contents

Sending a digital picture is very helpful in helping us to troubleshoot or answer any questions. PSoH Pressure switch open with high pump. This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally. The other pumps and the blower will purge for 30 seconds to 2 minutes at the end of the freeze condition. http://igroupadvisors.com/error-code/hot-tub-error-codes-dr.php

CTI Spa Side Error Codes For more information regarding CTI tech support click here th1/39 On startup indicates temperature probe problem. Switch closed while pump is deactivated. Gecko Error Codes also cover any control box manufactured by Gecko.For information regarding repairs click here If you need further help with troubleshooting click here Balboa | Gecko | Hurricane | Proceed step by step, and you should be able to find the cause of the FL, FLO or FLOW error code.

Balboa Hot Tub Error Codes

Do not enter the spa. The fundamental reason is water flow through the spa control system, if the water is not flowing at a rate to satisfy the switch, it will result in one of the If the error code goes away and you are getting the proper voltage then replace the pressure switch/flow switch. It automatically activates all of the pumps and the blower to circulate water and warm the plumbing.

PSoC Pressure switch open with circulating pump. Inspect the wire and plugs, check the spa water level and make sure water is flowing free and fast. Status of the heater element is unknown. Coleman Spa Error Codes These error codes are caused by a variety of reasons.

FL Spa water is more than 20° F cooler than the temperature set point. Vita Spa Error Codes Proper flow of water is inhibited or a flow switch has malfunctioned. Contact qualified service technician. https://spacare.com/spasideerrorcodes.aspx Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF.

Sn2 Nonfunctional temperature sensor. Hot Tub Error Code Oh For the complete list of error codes click here. Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.

Vita Spa Error Codes

FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. Check for clogged filter.FL2 = Pressure switch problem. Balboa Hot Tub Error Codes FLO Flow Switch (heater is deactivated. Marquis Spa Error Codes Do not use spa when temperature is flashing or the OH message is displayed.

Could indicate a flow problem. his comment is here If you are unsure of something or have any questions, please do not hesitate to contact us via Email. Categories Consumer Research for Best Hot Tub (100) hottubworks.com (127) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa There are 3 groups of error codes; Flow codes, relating to water flow, Heater codes, and Sensor codes. How To Fix Flo Error Hot Tub

The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature. Ecn Spa operating in Economy Mode. Std Spa operating in Standard Mode. this contact form Turn the power back on, you have five seconds to join the wires together, do not join them before you turn the power on.

If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected. Gecko Spa Pack Error Codes The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Following is a listing of all the possible messages along with their meanings.

Try to reset power to spa.

SnS Sensors out of balance. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Make sure that they are open.• Clean the filter(s), waterline skimmer and footwell suction for any blockage..• In extremely hot weather, check for proper cabinet ventilation.• Check for excessive filter duration. Coast Spa Error Codes Low Water Flow (LF, FLO), is the usual cause of an overheating (OH, OHH) spa or hot tub.

ICE Freeze protection. Leave a Reply Click here to cancel reply. PnL Communication between the panel and circuit board is faulty. ---- Watchdog" (spa is deactivated) A problem has been detected. http://igroupadvisors.com/error-code/hot-tub-error-codes.php Browse by Price $0 - $24.99 $25 - $49.99 Over $50 CUSTOMER SERVICE Contact Us Shipping Return Policy Privacy Policy Testimonials MY ACCOUNT View Cart Account Login Order Status MORE INFO

The countdown timer for the UB bulb needs to be reset (Section 12.8, page 58). OH Over heat. ICE Freeze condition. 55ºF detected. Categories Consumer Research for Best Hot Tub (100) hottubworks.com (127) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa

One sensor has detected 110º. Pressure switch is not working.SN = Non functional high temperature sensor. Contact ACC. If your water flow is perfectly fine, then you could have a problem with the thermostat or high limit switches used on older spa packs, which could fall out of calibration,

Rare system error. OH Overheating, water over 112° F. OHS Overheat. If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate

Sn3 Open or shorted sensor ( heater disabled). F4 Circuit Board temperature has exceeded acceptable limit. pump will operate continuously until the temperature rises above 45° F.OH = Over heat. F6 Freeze protection.

OH High temperature condition, has reached 110ºF. It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. When water doesn't flow fast enough through the heater, it removes less heat, and the temperature of the water increases. The Spa or Hot Tub Panel Displays: HL, HFL - This indicates that a substantial difference in temperature between sensors has been detected during heating. - This could indicate a flow

© Copyright 2017 igroupadvisors.com. All rights reserved.