Home > Hot Tub > Hot Tub Error Code 5n

Hot Tub Error Code 5n

Contents

Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. If your Master Spa code is not listed please call customer care 855-308-2149; we do offer limited technical support. Do not enter the spa. When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. this contact form

I disconnected the safety suction switchs/relays and had no luck. The temp says it is at 110. If all these test are checked and they did not solve the error code issues, then it is possible you have a defective hi limit sensor. Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading... try this

Balboa Hot Tub Error Codes

The SN code didn't go away even with time. SnA & SnB Spa is shut down. It could be a loose plug connection or bad wire, or it could be a problem related to water flow.

One of the sensors has detected that the spa water is 110°F. If you pay 3-5 grand for a tub you get about 5-8 years out of them before they start to become non cost effective to repair. It could be a loose plug connection or bad wire, or it could be a problem related to water flow. How To Fix Flo Error Hot Tub Sn3, HL, EO, E2, E3, Prh, Prr - these all refer to the heat sensors that are usually attached to your heater manifold.

Make sure that all jets are open, and nothing is blocking the spa drain cover flow. How To Fix Sn Code On Hot Tub Loading... Or, it could be a problem with the thermostat allowing the heater element overheat. http://www.spadepot.com/spa-error-codes.htm Both are secured with black plastic nut around the gray cable.

Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Marquis Spa Error Codes It keeps breaking right away. drops. Spa Guy 1,707 views 2:07 Master Spa FLO Code or No Heat Early 2000's Hot Tub How To FYI The Spa Guy - Duration: 2:54.

How To Fix Sn Code On Hot Tub

It keeps breaking right away.

If you check the stainless steel heater vessel you'll find a slot with a grey wire tucked inside. Balboa Hot Tub Error Codes Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way. Vita Spa Error Codes Ecn = Spa operating in Economy Mode.

I'm still at a loss. weblink Std = Spa operating in Standard Mode. Ahh no more problems. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Balboa Hot Tub Codes Sl

While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump. They are not the highest quality tub and they are inexpensive. Master Spa Parts 2140 W. navigate here You really can't troubleshoot any further without a replacement set of sensors.

dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Great Lakes Hot Tub Error Codes COOL = Spa water is more than 20° F cooler than the temperature set point. FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end.

If the problem comes back, try and unplug the sensors and switch where they are plugged in.

Also LMI metering chlorine dispenser pump and HotSpring Jetsetter I use and endorse TFtestKits TF-100 from http://tftestkits.net ~Remember TFP counts on your donations to keep this site ad free~ Reply With My Spa started up and has been working good for a week without any problems. SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure. Great Lakes Hot Tub Troubleshooting Check for clogged filter.

ILOC = Interlock failure - possible pump or ozone spike . (---) =Unknown water temperature. (Displays when first powered up after refill). hot = Overheating, water over 112° F. If you follow that wire from the heater to the control box you are likely to find it shares a connector with the temperature sensor. his comment is here Working...

Do not enter the water. Pumps will run automatically. Rating is available when the video has been rented. Working...

you can also get out of prime mode by pressing the temp controls. Share your referral link! Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Sign in to make your opinion count.

If the display shows only this message(blinking), the spa is shut down. All Rights Reserved. Autoplay When autoplay is enabled, a suggested video will automatically play next. If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate

Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. On some systems, an alarm will sound. dr = Inadequate water detected in heater. The next morning the SN code was back and the tub was off.

© Copyright 2017 igroupadvisors.com. All rights reserved.