Home > Hot Tub > Hot Tub Error Code E1

Hot Tub Error Code E1

Contents

FL2 = Pressure switch problem. It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. Loading... One sensor has detected 110°F. have a peek here

No corrective action is necessary. With your meter on ohms, check across the poles of the switch. Pr = When spa is first actuated, it will go into Priming Mode. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new!

Balboa Hot Tub Error Codes

Water temperature is above acceptable limits. It could be a loose plug connection or bad wire, or it could be a problem related to water flow. I'm losing faith that this company can deliver. No action is necessary.

All rights reserved. Close Yeah, keep it Undo Close This video is unavailable. There also could be a voltage problem, excessive voltage creates heat. Marquis Spa Error Codes Check for excessive filter duration.

You can follow any responses to this entry through the RSS 2.0 feed. OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. If the error code goes away and you are getting the proper voltage then replace the pressure switch/flow switch. http://www.hottubworks.com/blog/spa-error-codes-sn-sns-sn1-sn2/ FL1 = Water flow problem, inhibited or pressure switch malfunction.

Remove the spa cover and allow the water to cool to below 42.0° C. Great Lakes Hot Tub Error Codes One sensor has detected 118° F at heater. See MoreSee Less 1 month ago "Loving our Toronto spa, from Thunder Bay, Ontario, Canada. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Spa Error Codes

If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. Unplug and plug the pump back in. 2. Balboa Hot Tub Error Codes Clean the filter/skimmer if there is any blockage. How To Fix Flo Error Hot Tub The Spa or Hot Tub Panel Displays: Sn, SnS This indicates that the sensors are out of balance.If alternating with temperature, it may just be a temporary condition.

Sign in to add this to Watch Later Add to Loading playlists... navigate here Remove hot tub cover to speed cooling. When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. A replacement temp sensor for this code is worthwhile as even if it does not solve the problem you will have removed the most common fault from your diagnosis and have Vita Spa Error Codes

iPoolandSpaParts.net 56,726 views 2:14 10 Most Common Hot Tub Problems - Duration: 3:12. Happy Hot Tubbin’ Daniel Lara Hot Tub Works Tags: hot tub error code, spa error codes, spa trouble codes This entry was posted on Thursday, February 5th, 2015 at 9:19 Pump may also be deactivated). Check This Out Sn2 = Nonfunctional temperature sensor.

If tripping continues, call for service.• Deactivate spa lock Hercules Control Systems for Spas or Hot Tubs: OH = Spa temp exceeds acceptable limits FLO = Flow problem ICE = Freeze How To Fix Sn Code On Hot Tub If pump 1 was turned on due to this reason alone, this message will appear for up to two minutes right after very cold water is detected.Note: Internal freeze protection only They would not do anything, now the heater is not working.

In summation; when you have spa trouble codes of Sn, SnA, Sn1, Sn2.

Please unplug the pump and move to a warmer ambient temperature. You can leave a response, or trackback from your own site. Make sure they aren't touching anything. Great Lakes Hot Tub Troubleshooting If display shows only this message (blinking) spa is shut down.

Check the water level. Shut the spa power off, remove the filter and make sure all the jets are open. The Spa or Hot Tub Panel Displays: dr, dry This indicates that there is not enough water in the heater. this contact form FLO2 = Closed or shorted flow switch on system startup Spa Quip Spa Side Error CodesSpaQuip Davey Troubleshooting SpaQuip Davey error codes explained SpaQuip Davey resets for controllers err 1 (H20)

If alternating with temp, may be temporary condition. Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Heater is deactivated.FL1 = Water flow problem, inhibited or pressure switch malfunction. HFL = Substantial difference between temperature sensors detected.

FL = Flow. NOTE: Temperature sensors should be mounted in a sensor mount in the wall of the spa and not behind the shield on the heater manifold with the hi limit sensor. Note: A common programming mistake is overlapping filter times that may cause the spa to filter continuously.• Check the water level.• Check the water temperature with an accurate temperature thermometer. Power fluctuation in the secondary power line is causing the DC voltage to be low.

Sign in 5 0 Don't like this video? These error codes can be caused for several different reasons. way22good1 26,795 views 0:43 Replacing a Hot Tub Top Side Control Panel - Duration: 3:54. FLOW SWITCH (Heater is deactivated.

Make sure that all jets are open, and nothing is blocking the spa drain cover flow. One sensor has detected 118º F. I CE2 = Freeze protection. ICE2 = Freeze protection.

Loading... With the system powered off, you normally unscrew the sensors from the heater manifold, and unplug the wire from the panel.

© Copyright 2017 igroupadvisors.com. All rights reserved.