Home > Hot Tub > Hot Tub Error Code Flo

Hot Tub Error Code Flo

Contents

See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. I topped off the water, both were process of elimination and not required. strongtech1 88,558 views 5:05 How to Diagnose Your Hot Tub Pressure Switch for Flow Problems | Arctic Spas - Duration: 3:41. The PWA is the circuit board. Check This Out

Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. OHH = Overheat. Working... Leave a Reply Click here to cancel reply. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/

Where Is The Flow Switch On A Hot Tub

One interesting thing is that even though I have the temp set to 93, its listed on the panel as currently being 99 to 100 which is where it was before ian Ranshaw October 10, 2015 at 6:18 pm Hi. Home | Store Locator | Support | New Dealer Opportunities | Privacy Policy | Sitemap | Contact Us ©1997 - 2016Blue Falls Manufacturing LTD. ↑ Arctic Spas | USA

Hot Tubs

Home Hot Tubs Inflatable Spas Cheap Spas Moderate Spas Under $3,000 Over $3,000 Luxury Spas Small Hot Tubs Dream Star 2 Person Tub Hot Tub Service Hot Tub Parts Hot Tub Damon August 19, 2016 Reply Hi, I have a 2000 Sundance Altamar spa and Ive been troubleshooting a solid FLO message. You can leave a response, or trackback from your own site. Hot Tub Flow Switch Troubleshooting Categories Consumer Research for Best Hot Tub (100) hottubworks.com (127) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa

Or do I need to flip the breaker to get it back to normal? Hydropool Hot Tub Error Codes If you are unsure of something or have any questions, please do not hesitate to contact us via Email. IF all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance Spa.

You must be logged in to post a comment.

FLO2 = Closed or shorted flow switch on system startup Pinnacle OH = Temperature has exceeded 110Ā° F SN = Sensor failure FL = Flow/pressure switch stuck in closed position Spa Vita Spa Error Codes very important. Spa unusable. The filters have not been cleaned in a while.

Hydropool Hot Tub Error Codes

From here the troubleshooting takes you inside the spas service area and should be looked at by an experienced technician. Step 3. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ If all else fails contact our Service support team to book a spa diagnostic and repair of your spa. Where Is The Flow Switch On A Hot Tub When water isn't flowing fast enough through the heater, the FLO error code shuts things down, to avoid a total meltdown (well, not really a melt-down, but you know). Flc Error Code On Hot Tub Laurent November 08, 2015 Reply Hi, I have the same problem and tried to remove filter, release the air lock from the bib but still showing "Flo & Cool".

I know the pump and heater are obstruction free because I had them both apart in the last few days. his comment is here Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice. All of a sudden it began to to work again (going through cycles). softcellelectrical 117,217 views 9:12 Loading more suggestions... Sundance Hot Tub Flo Error

However, later in the day the message came back and has been on. Thanks for any help or suggestions. The filter is clean and both pumps run and the flo switch is new. this contact form Once again these can be caused by a flow issue.

It has maintained the temp for 3 days. Hydropool Hot Tub Flow Error Good luck! dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message).

This is normal until the spa reaches the desired temperature via topside or your spa is not heating due to thefact that your flow switch is not sensing proper water flow

By removing the filter you just removed the air lock. They either need to be chemically cleaned over-night in filter cleaning solutionĀ or replaced if they are 1 year old or older. I have checked my one big filter and changed it no fix, not sure if I have another filter, better look, water level good. Marquis Spa Error Codes I have a cal spa classic select -41. 7000 control panel. 2, motors.

Nigel August 19, 2016 Reply Damon if Summer Logic is causing the solid FLO it should go back to normal once the water cools. Reply Rebekah says: December 17, 2012 at 11:26 am Angie, We're not able to offer trouble-shooting services via our blog but feel free to call our service department to schedule a diy collaborative 12,054 views 17:46 How to Replace Your Hot Tub Pump | Arctic Spas - Duration: 5:52. navigate here The temp sensor is the larger of the two silver bullets.

It may be soiled/dirty/greasy, not to the naked eye. Filters are usually the number one culprit as people don't take the time to clean the cartridges often enough so the pleats get clogged and restrict the flow. But with my experience in such matters I suspect I will again see these warnings. Spa has shut down.

Sign in 10 Loading... If it does you know you need a new pressure switch. If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. Wait up to 1 minute to see if the error clears itself,if not reset the tub by turning off the GFI breaker, wait 1 minute, and then turn the breaker back

I have a hotsprings grandee and am not getting any circulation. I am a hardcore DIY, so is it time to start taking lines apart, which will begin to teach me things, plus I assume I will have to get a new Once this is done check ACROSS the heater element post, you should have either 110 volts or 220 volts depending on what voltage is operating the control box. We have circulation and water falls work.

The panel showed ‘dr' indicating no water in the heater. Any help would be great admin October 30, 2015 at 10:06 am Hi Shawn, If it is not the sensor than it must be the PC board itself. -Jay Jennie November

© Copyright 2017 igroupadvisors.com. All rights reserved.