Home > Hot Tub > Hot Tub Error Code List Sns

Hot Tub Error Code List Sns

Contents

Categories Consumer Research for Best Hot Tub (100) hottubworks.com (127) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa Heat Related Pump Not Primed. The following is a list of most probable causes of this message. SnS Sensors are out of balance. have a peek here

Press "Mode" Button to Clear Message. hot = Overheating, water over 112° F. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes Quick LinksHomeFeatured ProductsSpecialsNew ProductsAll Products ... http://www.hottubworks.com/blog/spa-error-codes-sn-sns-sn1-sn2/

Balboa Hot Tub Codes Sl

SN = Non functional high temperature sensor. The equipment stays on until the sensors detect that the spa temperature has risen to within 8.0°C of the set temperature. Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Then make a reset err 7 : Stuck Relay err 8 : No Temperature Data 01 : Stuck Button 02 : No Controller Data 03 : Temperature Sensor 04 : Water SE = Spa operating in Standard-in-Economy Mode. This could indicate poor flow or air bubbles in the heater. Balboa Sn Error Code Hold = Panel sensors have been pressed too many times in a short period of time.HOT = Circuit Board temperature has exceeded acceptable limit.ICE = Freeze protection.

I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address How To Fix Sn Code On Hot Tub Blocked Skimmer.4. Remove spa cover and let the water cool down. http://balboadirect.com/spa-panel-messages.aspx If the flow rate still seems less than normal with all jets and valves open, you may consider inspecting for broken valves (closed when they appear to be open), clogged impeller

Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. Cal Spa Hot Tub Error Codes PSoH Pressure switch open with high pump. Note: This auxiliary freeze protection functions at all times, even when another fault condition has occurred and has otherwise shut the spa down. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.SEoP = Sensor open or disconnected.

How To Fix Sn Code On Hot Tub

Press "Mode" Button to Clear Message. https://spacare.com/spasideerrorcodes.aspx HFL Substantial difference between temperature sensors detected. Balboa Hot Tub Codes Sl Back to Top rt9 or TEST GFCI Message Time to "Test GFCI Reminder" (rtg).Appears Every 30 Days*. Balboa Hot Tub Error Codes If you do not see water flowing from the circ pump outlet, IMMEDIATELY turn off power to the spa (as an attempt at heating will occur within a minute of the

Back to Top OHH, HH, or HTR TEMP LMT SERVICE REQD Message There is an "Over Heated Heater" (OHH or HH) Condition.One of the Water Temp Sensors has detected 118°F (47.8°C) navigate here Back to Top CFE or CONFIG ERROR Message There is a "Configuration Error" (CFE) in the Dip Switches or Configuration Settings.This Error Message indicates that the Dip Switch Numbers Displayed or Browse by Price $0 - $24.99 $25 - $49.99 Over $50 CUSTOMER SERVICE Contact Us Shipping Return Policy Privacy Policy Testimonials MY ACCOUNT View Cart Account Login Order Status MORE INFO With the system powered off, you normally unscrew the sensors from the heater manifold, and unplug the wire from the panel. Sn Error Code Hot Tub

CTI Spa Side Error Codes For more information regarding CTI tech support click here th1/39 On startup indicates temperature probe problem. Inspect these first:• Check slice or ball valves. The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue. Check This Out If there is No Error Message, Select "No Error Message" Below.

Quick View JavaScript seems to be disabled in your browser. Cal Spa Sn Error Code All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 7 Days, but some Spa Brands or Models may be Different. If your Master Spa code is not listed please call customer care 855-308-2149; we do offer limited technical support.

Contact Us My Account My Cart Log In Site Index Home Page MSP Rewards Contact Us Win Free Chemicals Owners Manuals Master Spas Care Guide Error Codes Policies & FAQ’s Review

You can also check the pressure switch or flow switch with a an Ohm meter. Product Technical Support Help Me Replace A Part Product Manuals Product Color Codes Spa Panel Messages Topside Panel Manuals Common Spa Problems System Cross Reference Home>Balboa Spa Panel Messages Balboa Common Heat Related Pump Not Primed. Balboa Hot Tub Codes F8 The Sensors are Verified Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors.

All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 7 Days, but some Spa Brands or Models may be Different. Ecn The hot tub is in Economy mode While in this mode your hot tub will only heat while it filters. Sn3 = Open or shorted sensor ( heater disabled). this contact form If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa.If your spa is not overheating based on physical vessel temperature and

Heat Related Pump Not Primed. If there is Now a Message Other than a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, that Message will Now have to be Diagnosed. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". Do not do this more than 5 times.

Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes Pump may also be deactivated). Spa has shut down.

It automatically activates all of the pumps and the blower to circulate water and warm the plumbing.Note: This auxiliary freeze protection functions at all times, even when another fault condition has HOT, OL, HL, FLO, Sn… SPA TEMPERATURE SENSOR ERROR CODE FLOW CHART Here's a Cal Spa troubleshooting chart for when your spa topside display shows a sensor error code Sn, Sn1, There is Not Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 =

Heater is shut down, but other spa functions run normally.

© Copyright 2017 igroupadvisors.com. All rights reserved.