Home > Hot Tub > Hot Tub Error Code Sl

Hot Tub Error Code Sl

Contents

Sep 13, 2009 | Balboa Instruments Duplex Digital Panel 2... Parts & Accessories back Accessories Hot Tub and Spa Parts Patio, Lawn & Garden Hot Tub 101 back Acrylic Hot Tubs and Spas Hot Tub Seating Options Common Technical Questions/Answers 5 user-manual-Balboa R574 System... Expand To Learn More The first thing to do is to narrow down and isolate the faulty part through the process of elimination. Check This Out

Low Water Level.2. Low Water Level.2. To display the set temperature, press “Set” once. dr = Inadequate water detected in heater.

Balboa Hot Tub Turn Off Economy Mode

GFCI breaker is still on, however, control panel displays  blank. This could indicate a flow problem. 'IC' "Ice" Potential freeze condition has been detected 'ICE' Auxiliary sensor detects potential freeze condition 'ICE' Potential freeze condition has been detected Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles.

I specialize in electrical questions and I am most familiar with spas that were manufactured by NEMCO, Regency, Hydro Spa, Gulfcoast Spas, Leisure Bay, and Premium Leisure. It turns on, moves some water well towards getting primed, then cuts off. SL will display when water temp is not current, and will alternate with water temp when the pump is running. Hot Tub Economy Mode This is an Operational Message, Not an Error Indication.

Closed Slice Valve.7. Heat Related Pump Not Primed.9. Press "Mode" Button to Clear Message. http://balboadirect.com/spa-panel-messages.aspx Expand To Learn More.

If there is Now a "CrC" or "CHKSUM FAIL" Error Message, contact your Dealer or Service Organization. Balboa Spa Control Manual Thanks, Jacque AnswerJacque, The "SL" you have on your display means that the spa is in "Sleep" mode in which case the heater does not come on. Test and Reset the G.F.C.I. Sleep Mode heats the spa to within 20°F/10°C of the set temperature only during filter cycles.

Ec Code On Hot Tub

Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times Standard – St, Std Standard is the default setting, and you are in standard mode if none of the other setting codes show up 1. Balboa Hot Tub Turn Off Economy Mode Do not use spa when temperature is flashing or the OH message is displayed. How To Get Hot Tub Out Of Economy Mode With the Heat Related Pump Running, wait at Least 2 Minutes for the Correct Actual Water Temperature to be Displayed.

PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. his comment is here Contact your Dealer or Service Organization. COOL = Spa water is more than 20° F cooler than the temperature set point. Common Technical Questions/Answers Home / Hot Tub 101 / Common Technical Questions/Answers You will find answers for some common questions that our technical team hears from customers on a Balboa Hot Tub Error Codes

It was advertised 11/21/2016 11/21/2016 Poolservice123 I got this Aqua Cal superquiet pool heater with code reading 11/20/2016 11/20/2016 Poolservice123 I have a 1997 hot tub that wont heat. In this case, if the extreme conditions are determined, the spa will display the StU message until the spa is shut down It will also set the HOt flag (HOt does There may Not be Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. this contact form Do not enter the water.

Therefore, "OHH" is considered to be a Flow Related Error.Check for All of the following Conditions:1. Hot Tub Modes Remove, Clean, and Reinstall Spa Filter Cartridge per Manufacturers Instructions. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in

This list if far from complete and covers older model controls. '- -' Temperature Unknown 'Cool' Water temp 20 below set point 'dr' Possible inadequate

The GFCI can also be tripped manually via the Edit Menu interface titled gFC.Button press instructions for initiating a GFCI trip manually can be found HERE.If the spa is not installed prev next Related Questions: 1 Answer The instrumentation panel says "SL" and the spa isn't heating.How do I get it to heat again? The sensor plugged into sensor “A” jack is malfunctioning.Contact your store if you continue to see this problem. Sl Code OHS = Overheat.

of heater tests.Take same actions steps used for dr. Read our FAQ! So to get it out of the SL mode and into one of the other modes you have to push a sequence of buttons, most likely the "Temp" button quickly followed navigate here The Water Temperature is Always maintained within 1°F (.5°C) of Set Temperature.

Ec will display when water temp is not current, and will alternate with water temp when the pump is running. Refer to your owner's manual. Low speed may run automatically at times, during which it cannot be deactivated from the panel, but high speed may be operated. If the Error Message has Not Cleared, the Spa Water is still too Hot to Continue Testing.• Either Wait for the Spa Water to Cool Below 108°F (42.2°C), or Exit Now

Pumps turn on at regular intervals to check and maintain temperature 3. Low Water Level.2. ShowMore How to disable SL sleep mode on the hot tub?I have shut it off and restarted. Standard mode maintains the desired temperature.

System will Auto Reset when Water Temp is below 108°F (42.2°C). Back to Top PHL or PH IS LOW RAISE PH Message At the pH Sensor, the "pH Level is Low" (PHL).With a pH Sensor Installed in the System, the pH Level Posted on Aug 30, 2010 Helpful 16 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a Heat Related Pump Not Running.8.

HLoH = Hi Limit Over Heat. Closed Slice Valve.7. A service technician must carefully evaluate the pumps and circuit board before allowing the spa to run again.Check For Suction Blockage:1. code displayVerify that all the knife valves are open.

© Copyright 2017 igroupadvisors.com. All rights reserved.