Home > Hot Tub > Hot Tub Error Codes Balboa

Hot Tub Error Codes Balboa

Contents

Back to Top rtC or RTC FAILURE Message The "Real Time Clock" (rtC) Cannot be Read.At Power-Up, the System Board Real Time Clock could Not be Read. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different. ToE Time out error. The Heater and Pump will Operate Any time the Thermostat Demands Heat. Check This Out

Other Heating Modes are Economy, Standard in Economy, and Sleep Modes.Note: On the Panels that Display the "Std" or "St" Messages, the Message will Only be Displayed for a Few Seconds Drain and Refill the Spa Water per Manufacturers Instructions. No action is necessary. dry Inadequate water detected in heater. (Displays on third occurrence of "dr" message). http://www.spadepot.com/spa-error-codes.htm

Sl Code On Hot Tub

SN = Non functional high temperature sensor. If you still have problems, check over your temp sensor and hi limit circuits for wire or plug or sensor problems. Do not enter the spa.

Back to Top PHH or PH IS HIGH LOWER PH Message At the pH Sensor, the "pH Level is High" (PHH).With a pH Sensor Installed in the System, the pH Level For Low Flow spa error codes, check the filter, check the pump and check the valves to find something that is obstructing the water flow. ILOC = Interlock failure - possible pump or ozone spike . (---) =Unknown water temperature. (Displays when first powered up after refill). Vita Spa Error Codes Do not use spa when temperature is flashing or the OH message is displayed.

PSoC Pressure switch open with circulating pump. Balboa Hot Tub Turn Off Economy Mode All Pumps and Blower are ON for at least 4 Minutes After Temp is 45°F (7.2°C) or Above at the Sensors, or when the Aux Freeze Switch Opens. Any and all service should be performed by a licensed spa technician. https://spacare.com/spasideerrorcodes.aspx If alternating with temp, may be temporary condition.

ILOC Interlock failure - possible pump or ozone spike. (---) Unknown water temperature. (Displays when first powered up after refill). Hot Tub Control Panel Instructions If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. Sn1 Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated).

Balboa Hot Tub Turn Off Economy Mode

Heater disabled but the spa is operational. FLO* = Flow Switch (heater is deactivated. Sl Code On Hot Tub Since it was so cold, and my spa was in sleep mode, I opened the panel and made sure there was water ( not ice) in the heating element. (I cracked Balboa Hot Tub Codes F8 Sundance Spa Side Error Codes For more information regarding Sundance tech support click here ILOC Interlock failure - possible pump or ozone spike FLO Pressure switch malfunction Hold Panel buttons pressed

It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. his comment is here This is an Operational Message, Not an Error Indication. Entire system is disabled. Contact your Dealer or Service Organization. Spa Command Panel Instructions

Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 365 Days, but some Spa Brands or Models may be Different. Entire system is disabled. this contact form To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.

If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:- How To Get Hot Tub Out Of Economy Mode One sensor has detected 110ยบ F. When water isn't flowing fast enough through the heater, the FLO error code shuts things down, to avoid a total meltdown (well, not really a melt-down, but you know).

Back to Top rSA or CK SANITIZER Message Time to Check "Sanitizer Level Reminder" (rSA).Appears Every 7 Days*.

It could be a loose plug connection or bad wire, or it could be a problem related to water flow. Sn2 = Nonfunctional temperature sensor. or SpaDepot.com customers with accounts enjoy these benefits: Faster checkout Order status & history Easier package tracking Manage addresses Favorites list Exclusive deals CREATE ACCOUNT SHOP AS GUEST All Products Balboa Hot Tub Troubleshooting Too Many Closed Jets.6.

This Mode allows the User to Replace or Clean a Pressure Side Filter Cartridge without Equipment turning ON unexpectedly. Back to Top SAH or SANITIZER HIGH Message At the ORP Sensor, the "Sanitizer Level is High" (SAH).With an ORP Sensor Installed in the System, the Sanitizer Level is Above 830 FC Freeze protection. navigate here It turns out it was the fuse in the control system.

Contact your Dealer or Service Organization.SnS or Sn is Blinking ON and OFF:There is a Verified "Sensors out of Sync" (SnS or Sn) with Each Other Condition. Blocked Suction Fitting.3. Topside controls also give lots of information about your spa status, which are not to be confused with spa error codes. You can follow any responses to this entry through the RSS 2.0 feed.

Heater is shut down, but other spa functions run normally. HFL Substantial difference between temperature sensors detected. dr Inadequate water detected in heater.. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1.

Could indicate a flow problem. Hold Panel sensors have been pressed too many times in a short period of time. My owners manual confirms that the spa will be disabled if the Sn code displays. drops.

Heater is deactivated. In summation; when you have spa trouble codes of Sn, SnA, Sn1, Sn2.

© Copyright 2017 igroupadvisors.com. All rights reserved.