Home > Hot Tub > Hot Tub Error Codes Sl

Hot Tub Error Codes Sl

Contents

If you hear the pump humming check but no water movement you may have air trapped in the pump. System will Auto Reset when Water Temp is below 108°F (42.2°C). If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:- Your best option is to get a spa tech/engineer out to investigate the problem. Check This Out

Refer to your owner's manual. If you have no power, the fuse is good and the breaker is not tripping you may have a problem with the breaker. Pump may also be deactivated). As a responsible adult, always check the topside control panel display for errors and verify safe water temperature before using a spa, and before allowing children to use a spa.

Balboa Hot Tub Turn Off Economy Mode

Both are secured with black plastic nut around the gray cable. If there is Now a Message Other than a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, that Message will Now have to be Diagnosed. It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. On them you need to press the 'TEMP' button and then the 'LIGHT' button within three seconds of each other and this will change the modes from EC (economy mode), to

This code could signify the unit has a flow problem.Check the level of the water in hot tub unit and refill levels if needed. Product Technical Support Help Me Replace A Part Product Manuals Product Color Codes Spa Panel Messages Topside Panel Manuals Common Spa Problems System Cross Reference Home>Balboa Spa Panel Messages Balboa Common Parts & Accessories back Accessories Hot Tub and Spa Parts Patio, Lawn & Garden Hot Tub 101 back Acrylic Hot Tubs and Spas Hot Tub Seating Options Common Technical Questions/Answers 5 Balboa Hot Tub Codes F8 There is Not enough Water in the Heater to Start it.

Flip the switch down then to the up position if it seems to stay up and you still have no power going to the spa try pressing the test button on Balboa Hot Tub Error Codes In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced. this information is being provided for informational purposes only. http://balboadirect.com/spa-panel-messages.aspx If it's not flowing after two minutes, turn the power off and let the spa rest for a few hours, then repeat.

Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in Hot Tub Control Panel Instructions Too Many Closed Jets.6. The wireing in the motor has a small short that will get worse soon enough and may even catch fire if the conditions are right. Your fault will either be with the keypad connection on the PCB within the spa pack.

Balboa Hot Tub Error Codes

Do not let the pumps run for a total of more than 2 minutes if they haven't primed by then. http://www.strongspas.com/common-technical-questionsanswers I specialize in electrical questions and I am most familiar with spas that were manufactured by NEMCO, Regency, Hydro Spa, Gulfcoast Spas, Leisure Bay, and Premium Leisure. Balboa Hot Tub Turn Off Economy Mode Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. How To Get Hot Tub Out Of Economy Mode Back to Top gFI or GFCI FAILURE Message The Control System Could Not Trip the "GFCI" (gFI).The spa has determined that a GFCI is NOT properly installed in the circuit providing

Closed Slice Valve.7. his comment is here After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If you have difficulty locating these wires or junctions please refer to the diagram located on the removable cover. Doing so may cause damage to the pump and cause the system to go into an overheat condition.If after repeated attempts (hours apart) you still cannot get all pumps to prime, Ec Code On Hot Tub

The blower and pumps activate automatically in spite of the status of the hot tub unit.SY or STBYMeans the hot tub unit has entered Standby mode.Check that the Microfilter is in The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2. After the Problem has been Resolved, you Must Press Any Button to Reset and Restart Heater Start Up. this contact form Read our FAQ!

Try Turning the Power OFF and back ON again, or Continue for a Detailed Test Procedure.1. Spa Command Panel Instructions Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct.

For information regarding repairs click here.If your spa is not overheating and you are getting the above error codes then a couple of things could be happening.

Pumps and Blower can be turned ON and OFF to Remove any Air from the Heater. Expand To Learn More Test or replace .3amp fuse next to terminal box where wiring attaches to the spa. The power was shut off to the hot tub. Balboa Hot Tub Troubleshooting Drain and Refill the Spa Water per Manufacturers Instructions.

Spa is shut down for 15 minutes. 'dry' Inadequate water detected in heater 'Enc' Spa is operating in Economy Mode. Spa is shut down. Back to Top - - F, - - C, or - - Message The Actual Water Temperature is "Unknown" (- -).Priming Mode has been Exited and the Pump has Not yet navigate here Take out the Microfilter and clean or replace it.2.

NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 30 Days, but some Spa Brands or Models may be Different. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. Comment Flag More Print this page Share this page You can't post conmments that contain an email address. × Comment Anonymously Video Images 1 Answer Charles East Level 2: An expert

There may be conditions that exist in which the spa control system will be unable to detect these conditions. Spa not maintaining temperature or showing SL, SLP, EC or ECO codes? It should be able to support 30 jets just fine.

© Copyright 2017 igroupadvisors.com. All rights reserved.